MACE Motion Detector Model 80200

Mace Motion Detectors unique passive infra red system concentrates on the protected area you select. The motion detector studies the area and responds only when a person moves into the protected area... and then turns on the alarm. In the Entry Chime mode, the chime will Ding each time motion is detected.

Features:

Important Safety Tips
  • Motion sensor detects motion & activates alarm.
  • Programmable security code and entry delay timing.
  • Adjustable sensor head.
  •  Built-in high output 105dB alarm.
  •  Alarm/door chime option.
  •  Panic button.
  •  Program & low battery indicator.
  •  Verification tone for key pad and arm/disarm.
  • 9V battery operated (battery not included) & AC adaptor compatible.

Installation

1. Remove the screw from battery compartment
cover, slide it down to remove the cover.

2. Install an alkaline 9 Volt battery.

3. Replace the battery cover and replace the screw.

4. For wall mount:
Using the battery cover as a template, mark locations of holes and install anchors and screws. Place the unit over the screws and slide the unit down to secure in place 
Or, as an option, you can USE Velcro (not included) to install the unit anywhere you see fit.
We suggest that you mount the unit at between 3 to 6.5 feet (1 to 2 meter) above the floor for best coverage of protection area. Adjust the sensor head to left, or right for the best direction of your detection area.

5. For shelf-top:
Turn the sensor head clockwise to 180 degrees to the back, then turn the head upwards to a desired angle. Place it on the shelf top location you selected.

6. To use AC adaptor (Not included):
Use the AC adaptor with output 9 Volt DC 200 MA with 3.5 mm diameter male plug, center positive(+) plug to the adaptor jack on the side of the unit. 

Operation

1. TO ARM THE UNIT -
(A) Enter your security code (or "0-0-0", if you did not change the code).
(B) Press "ARM", you will hear 3 short beeps to confirm "ARMED".

NOTE:
- Make sure to switch off the chime switch before arming.
- There will be a beep after 60 seconds sensor warm-up, and exit delay after arming the unit.

2. TO DISARM THE UNIT -
(A) Enter your security code.
(B) Press "DISARM", you will hear one beep to confirm disarming.

3. DOOR CHIME ON/OFF -
(A) Slide the chime switch to "ON"
(B) Wait for 60 seconds after a beep for the sensor to "WARM-UP". Then when human movement is detected, it will sound "DING DONG chime.
(C) Slide the switch to "OFF" to turn the chime function off.

NOTE: When unit is in arm mode, the chime will not function.

4. PANIC BUTTON -
(A) Press "PANIC" button to trigger alarm immediately for 30 seconds.
(B) To stop the alarm, just enter your security code and press "DISARM".

Battery Low Indicator

When 9V battery goes low, the LED will flash once every 3 seconds to indicate the low battery - in arm mode only. The LED will not indicate low battery in disarm mode - for power saving reasons.
NOTE. The battery low LED indicator only works
for the 9V battety. Change a new alkaline 9V battery immediately, or else the sensor might not detect properly.

Intrusion Memory Indicator

When you disarm the unit, if the LED flashes 3 times, it indicates that there has been intrusion during the last arming mode. Be sure to check your home/ office thoroughly after entering.

 

 1 . Do not install alarm where it will be exposed to direct sunlight or rain.
2. The alarm siren is very loud, never put the unit close to your ear.
3. The unit should be directed away from heat sources such as radiators, heating ducts and stoves.
4. If the unit goes off at random, it is possibly located too close to a heat source. Changing the location or direction of the unit can remedy this.
5. If the unit messes up during the programming procedure, becomes abnormal, or if you forgot the "PASSWORD", take out the battery and wait for about 3 minutes for unit to rest, replace the battery. The system will reset to the initial normal state for you to re-program.
6. The unit can provide valuable protection for your home and property if utilized properly. However, this unit cannot guarantee complete protection against burglary or robbery, therefore, we will not be held responsible for any loss or damages which could occur.

Programming Settings

NOTE.* The security code is Initially factory-set at "0-0-0" when you first put in the battery. You can program your own security (up to 6 digits). if more than 6 digits are entered, you will hear an error tone.

1. To program security code after battery installation: 
(A) Press the digit "0-0-0". 
(B) Press the "PROG" button. 
(C) Enter your new code number. (1-6 digits). (D) Press the "PROG" button again.

2. To change existing code to a new code: (A) Enter the old code number. (B) Press the "PROG" button. (C) Enter your new code number (1-6 digits). (D) Press the "PROG" button again.

3. To program the alarm timing: 
(A) Press "PROG" button. 
(B) Press one of number " l ", "2" or "3" for different timing.
 "1" - 30 seconds alarm 2 cycles, 30 seconds rest in between. (Preset timing)
"2" - 60 seconds alarm 2 cycles, 30 seconds rest in between.
"3" - 90 seconds alarm 2 cycles, 60 seconds rest in between.

4. To program the entry delay timing:
(A) Press "PROG" button.
(B) Press one of number "7", "8" or "9" for different timing.
"7" - 15 seconds delay. (preset timing) 
"8" - 8 seconds delay. 
"9" - 0 seconds delay. (Instant alarm)

REMARKS:
The programming can only be operated during
disarm mode. When unit is in arm mode, no
programming is allowed for added protection.

To Test Detection Area

After selecting a location for installation of the unit, you can turn the chime on.and wait for 60 seconds for "WARM UP". Then you try walking in front of the unit. When the unit detects motion, the chime will (B) NO ALARM sound. There will be no chime sound if you walk beyond the detection range. By testing the detection range, you can adjust the location, the sensor angle for best coverage. Turn the chime off after you test.

Troubleshooting Guide

(A) CAN NOT ARM/DISARM
- Make sure you've entered the correct "security code". If not, re-enter the correct code.
- If still doesn't work. Remove the 9V battery, wait for about 3 minutes, replace battery. Then try "ARM" & "DISARM" again.

(B) NO ALARM
- Check to see if battery is low. It so, replace
new battery.
- Remove the 9V battery, wait 3 minutes, replace the battery. Then try to see if alarm works.

(C) ALARM SOUND LOW AND SENSOR NO DETECTION
Check to see if battery is low. If so, replace new battery.
Back to Home Security